Keywords: best table saw for dado cuts, table saws that accept dado blades, table saws with dado capability, dado blade, top saw for dado, portable table saw.
Looking for table saws with dado blades? As of now, no manufacturer includes dado blades with their table saw. You have to buy them separately. Can you use a dado blade on any table saw? No, you cannot use a dado blade on any table saw. There are particular table saws with dado capability.
A dado blade is a circular saw blade that allows you to cut wider curves in wood than a regular saw blade. Dadoes are made by wobble dado blades, or stacked dado blade sets cannot be cut by just any type of table saw. Because the arbor on most table saws is too short, they are unable to fit dado blades.
There are specific table saws that accept dado blades. In this article, we will talk about mainly some portable table saw or jobsite table saws which can accept a dado set. These table saws are best for beginners also.
The are several dado capabilities table saws in this group, but some of them, like the DeWalt table saw DWE7491 that accepts dado and have optional dado throat plate built for them specifically.
This article will also provide you information on some of the best table saws for dado cuts currently available on the market. If you are planning to upgrade your workshop’s capabilities by purchasing a table saw with a dado blade, this article will walk you through all the basics of dado blades and the table saw that can use dado blades.
You’ll also learn how to cut a dado with a table saw, how to install a dado blade on a table saw, as well as basic safety practices while utilizing a dado blade on a table saw with dado capacity.
Caution: Never try to use a table saw with a short arbor with a fully stacked dado blade set. Before fitting the dado blade, read the manual and check sure the table saw can use it.
Types & Sizes of Dado Blades
Dado blades are used in all woodworking workshops, especially by those who make cabinets, shelves, and other DIY projects that require dado grooves. These dado grooves may be created in one cut and range in size from 1/4 inch to 13/16 inch in width.
Since this table saw blade is not for thorough cuts, normally, 8-inch dado blades are manufactured for 10-inch table saws. Blades with diameters of 6 and 7 inches are also available.
The maximum width that may be achieved is roughly 1 inch, and nearly any measurement smaller than that is possible. Dado blades may be used to make 4 types of joints:
- Dado and groove
- Tongue and groove
- Half lap
There Are Two Kinds of Dado Blades Available
Wobble Dado Blade
A wobble dado blade is a single blade that rotates at an angle. It doesn’t wobble, but it does sway when cutting, creating an S pattern inside the plate width that you may tune to your preferred cut width. The cuts are not as clean as the stacked dado blade type. This type of cutting with a table saw, on the other hand, is easier and more convenient because no spacers or inserts are required. But also has some safety concerns.
Stacked Dado Blade
A stacked dado blade is made up of many blades stacked together to produce a wider blade. To obtain a precise cut, these blades can be alternated with spacers and chippers. Chipper blades can be used depending on the cutting width. The length of the cut is also determined by the chippers. For its high performance, safety and adaptability, craftsmen prefer stacked dado blade sets.
6 Best Table Saws that Accept Dado Blades
Model & Features
Top-Rated Table Saw’s Stacked Dado Blades
Best Table Saw with Dado Capability – Detailed Reviews
Now let’s see in details the table saws we choose which are the best dado compatible table saws on the market today.
1. DeWALT Table Saw with Dado Capability (DWE7491RS)
The DEWALT DWE7491RS table saw is one of the best DeWalt table saws that accept dado blades and dado sets.
This 10-inch Jobsite Table Saw can take an 8-inch dado blade with a maximum width of 13/16 inches. With a rip capacity of 32.5 inches, this DeWalt table saw with dado can easily cut through larger trim and shelf materials.
A throat plate designed for DEWALT DWE7490, DWE7491 versions is available separately from the manufacturer. The wheeled base makes this table saw model a good alternative if your shop needs you to relocate power tools while they are not in use.
It also comes with a rolling stand for easy transportation or just moving around the workshop or jobsite. Push Stick, Blade Guard, and Wrenches are among the other safety features included in the table saw’s design. Rip Fence, Riving Knife, Miter Gauge, and the instruction manual are among the additional accessories included in the kit.
Overall, the DEWALT DWE7491RS table saw is the best table saw with dado capability.
2. DeWALT DWE7491X 10 In. Table Saw with Folding Stand
One of DeWALT’s most recent portable table saw with dado capability is the 7491X. It’s a step up from the legendary DeWALT 7480.
This table saw is simple to use, thanks to onboard storage and a rack-and-pinion fence. The fact that DWE7491X accepts dado blade is relevant in this scenario.
This DeWalt table saw can take a dado set with dado blades up to 13/16 inches in length. It’s not a good idea to try to stack dado blades that are wider than this.
You should also avoid utilizing dado blade with a diameter greater than 8 inches. You’ll be needing a Dado Throat Plate, which is also available from DeWalt (DWE7402D1).
When installing the dado, you must purchase the required dado insert separately. Because dado cuts aren’t through-cuts, they must be done only after the blade guard assembly has been removed.
First, pull the riving knife and blade guard release lever, and then simply pull the blade guard and also the riving knife.
3. SKIL 15 Amp 10 Inch Table Saw with Folding Stand – TS6307-00
This is a cost-effective jobsite table saw with dado portable and powerful. For stability, it comes with a heavy-duty folding stand but no wheels.
This job site table saw can use dado blades. It can handle 8-inch dados blades cutting up to 13/16 of an inch, and the dado cuts are excellent.
This jobsite table saw is compatible with dado stacks too. You’ll need the right table insert (Dado Insert Plate for Table Saw TS6307-00), and a dado stack of 5/8 inch or less would suffice.
It also comes with a miter gauge and a self-aligning fence that uses the EZ View. Blade guard, miter gauge, rip fence, push stick, dust port elbow, anti-kickback pawl, riving knife, 24T saw blade, and wrenches are included with the jobsite table saw and integrated folding stand.
4. BOSCH 10 In. Job Site Table Saw 4100XC-10
When it comes to table saws with dado capability, the BOSCH 4100XC-10 Jobsite Table Saw is unquestionably one of the more costly alternatives.
Using the Bosch TS1007 Dado Insert, this model can also allow 13/16-inch dado blade. This makes it perfect for woodworkers who make dado grooves that are close to an inch in size on a regular basis.
The Bosch 4100XC-10 is a 10-inch worksite table saw that combines the benefits of a good contractor table saw with the mobility of a tabletop saw. A wheeled stand, guard, square-lock rip fence, miter gauge, push stick, and two wrenches are among the tools included in the box.
It stands out from its predecessors, such as the Bosch 4100-10 and 4100-09 models, thanks to a reduced size, changes to the barrier guard, and a more easily accessible big stop button.
5. Delta 36-6023 10 Inch Dado Compatible Table Saw
One of the first things a new construction professional should look for in a good jobsite table saw.
This saw is comparable to the DeWALT DW745, with the exception that it is somewhat heavier. Nonetheless, for smooth cuts on woodworking projects, this is a great portable table saw with dado for a novice.
The Delta 36-6023 saw offers all of the features you’ll need to make superior cuts, including a great rip capacity, accurate rack and pinion fence rails, and sturdy build. The blade of this saw is driven by a powerful 15-amp contractor-grade motor that can cut through most hardwoods.
6. Metabo HPT C10RJ Jobsite Table Saw (formerly Hitachi C10RJ)
The C10RJ is a portable jobsite table saw by Metabo (previously Hitachi). The Hitachi C10RJS 10″ Jobsite Table Saw is essentially the Metabo HPT Jobsite Table Saw. The only thing that changed was the brand name.
This saw is ideal for DIYers and hobbyists who don’t have enough space in their workshop for a full-size contractor or cabinet saw.
The C10RJ portable jobsite saw can also accept an 8″ x 13/16″ dado set, allowing you to complete a variety of woodworking projects.
The C10RJ may be operated on a benchtop or mounted on its accompanying wheeled base that folds up for storage, despite being larger and heavier (96 lbs) than comparable portable table saws.
The extendable side table provides for more ripping capacity. Ripping plywood or cutting different types of wood may be done effectively with the 15 amp powerful motor that spins at 4,500 RPMs. Onboard storage for extras such as the blade guard, anti-kickback pawls, push stick are also available.
With the soft start and electric brake turning it off and on this table saw is very easy.
Best Table Saw for Dado Cuts: Buyer’s Guide
Having the right information and technique will ensure that the best table saw with dado capability is lying right inside your workshop at the end of the day, whether you are a professional woodworker or a hobbyist.
The Top-Rated table saws for dado cuts consist of the same features as a conventional table saw, but with the addition of making dado cuts. The following are two of the most important considerations to make when purchasing a table saw that can use dado blades.
Arbor Size Compatibility
The arbor size of the table saw is the most significant element when it comes to the dado cut capacity. The width of the spinning motor arm, or how much thicker of a blade may be placed on it, is referred to as arbor size. Because the dado cuts employ two standard blades with chipper blades in between to reach your desired thickness, the wide arbor you can find is essential.
Make sure your table saw’s arbor can accommodate the dado blade set. When trying to get the blades and chippers mounted, don’t scrimp on spacers, washers or other components.
Motor Power and Blade Size
Next, check to see if your table saw can handle the dado blades. Minimum RPM ratings or other power indications should be provided by the blade set. Follow these tips to keep the blades from bogging down and causing kickbacks while you cut.
Depending on the type of materials you’ll be working with, you may look for a less expensive portable low-powered table saw, or a more expensive high-powered table saw for hardwood, etc.
Table Saw with Dado Capability: FAQ
What Size Dado Blade for A 10″ Table Saw?
An 8″ inch dado blade is recommended for a 10″ table saw. The bulk of dado sets are 6″ or 8″ in diameter for a reason. Most table saws aren’t powerful enough to run a 10″ dado blade. A 10″ set requires 25% more torque than an 8″ blade and 67% more torque than a 6″ blade.
The size of the dado that can be utilized on a machine is determined by the manufacturer. They make this decision based on the arbor, power transmission system, and motor design, as well as safety concerns and other variables that impact the best dado size. Some 10″ saws are only capable of making 6″ dadoes. Dadoes cut a lot more material than a normal blade and are also more demanding on the saw. So, only use the saw size recommended by the manufacturer.
Does DeWalt DW745 Accept Dado Blades?
Unfortunately, the DeWALT DW745 does not accept dado blade (stacking dado blade set) or a wobbling dado blade, as you can see on DeWALT’s site.
How to Cut a Wider Dado with A Small Arbor Table Saw?
A table saw with a short arbor could be able to fit just the two outer blades of the set, as well as a chipper, to make 3/8-inch to 1/2-inch dado grooves. This does not, however, limit you to 1/2-inch dadoes. Making two passes is a simple solution. While it takes a little longer to make the dado, it is less demanding on your saw’s motor and far safer than using a dado blade on a small arbor.
Will a Stacked Dado Blade Fit on Your Table Saw?
The arbors on many small to medium-sized portable table saws are too short to securely support a full stacked dado blade set. When using a single saw blade, this isn’t an issue, but when using a stacked dado blade with a chipper blade, there isn’t enough thread to properly grip the nut onto the arbor.
While there is no way to lengthen an arbor to make it longer and using a dado blade that doesn’t fit can be dangerous, there are a few options for solving this problem.
- Buy a table saw that supports wide dado blades.
- Buy a wobble-style blade. But stacked dado sets are safer and easier to work with. In comparison to the stacked dado, you can hear the motor work harder while using the wobble blade.
- Additionally, purchase the lowest diameter dado blade that will suffice for the job. Because you’ll be making wider cuts than with a single blade, it’ll help with performance.
- Last but not least, dado blades are time-saving. If you only need to make a few dados, instead of changing the blade, you may cut both edges of the dado and then chip away at the middle with your blade in repeated cuts.
How to Safely Use a Dado Blade Set?
Safety is the key to fully appreciating your woodworking experience, both in the short and long term. So, here are some safety tips when making dado cuts with a table saw:
- Maintain control of the workpiece to avoid kickback by utilizing feather boards, push sticks or a power feeder.
- Keep your pressure against the fence and downward to maintain a consistent cut depth.
- Even if the blade is covered by the stock, use push blocks and avoid placing your hands directly over it. Never attempt a through cut with a dado stack.
- When working with power tools, always wear eye and ear protection and properly fitted clothing.
- When it comes to the dado blade set, make sure the labeled side of the circular blade faces outward.
- Also, make sure that the teeth of each chipper blade are slightly offset while assembling your dado set. This will allow for a smoother cut and a cleaner dado.
- When possible, use a sled. As you proceed towards the dado cut, this will help maintain the work aligned and keep your hands away from the cutting area.
Which DeWalt Table Saws Accept Dado Blades?
Not on all DeWalt table saw accepts dado. These are the good ones that have dado capability:
- DeWalt DWE7491RS
- DeWalt DW744XRS
- DeWalt Dwe7490X
How to Make a Dado Cut with A Table Saw?
Here is a video showing how to cut a dado with a table saw.
How to Install Dado Blades on A Table Saw?
Here is a video showing how to install a dado blade on a table saw
Do All Table Saws Use Dado Blades?
As we said previously, not all table saws use dado blades. There are specific models that are capable of using dadoes. Check the best table saws above if you are looking for best compatible table saws.
Can Job Site Table Saws Accept Dado Blades?
Yes, if the arbor is wide enough. We usually advise using dado blades on table saws that allow them. We recommended several jobsite table saws above.
Are Dado Blades Illegal in The UK?
No, Dado blades are not banned in the UK. The HSE’s official view is that dado sets are OK as long as the table saw was designed to take them and the proper safety precautions are followed.
Best Table Saw with Dado Capability – Conclusion
With all of the information, we’ve provided, from thorough and honest product reviews and buying guide, choosing the right table saw for dado cuts should no longer be a challenge.
This article will help you evaluate their strengths and shortcomings, which will be able in assisting you in finding the best table saw for your DADO CUTS!